How does the litter robot know when it’s full?

The Litter-Robot relies on the Cat Sensor to know when your cat is inside the Globe and when it’s time to run a Clean cycle. Here’s how it works: Each time the unit is powered on and at the end of each cycle, the Cat Sensor measures the weight of the unit to use as a baseline.

What happens if you overfill Litter-Robot?

Fill the globe with approximately 8-10 pounds of litter, until it meets the raised “fill line” on the black rubber globe liner when spread flat. If there is too much litter in the globe, it will be expelled into the waste drawer during the first few cycles.

How often does Litter-Robot need to be emptied?

We recommend emptying and cleaning the inside of the globe every one to three months. Learn how to clean your Litter-Robot: 1. Press the Empty button to cycle the globe clockwise, which will allow the litter to fall through the waste port and into the drawer for easy disposal.

THIS IS UNIQUE:  What is the purpose of the controller in a robot?

How does the Litter-Robot cat sensor work?

The Litter-Robot relies on the Cat Sensor to know when your cat is inside and when it’s time to clean up. … Each time the unit is powered on and at the end of each Clean cycle, the Cat Sensor measures the weight of the unit. The Cat Sensor then uses that weight as its new baseline.

How do I keep my Litter-Robot from smelling?

Replace the Carbon Filter and Seal Strips periodically.

Keep the Litter-Robot smelling fresh by trapping unpleasant odors in the Waste Drawer with replacement Carbon Filters and Seal Strips (or buy them together).

Why is the blue light flashing on my Litter-Robot?

You’ll most commonly notice a flashing or blinking blue light on your Litter-Robot control panel. This blue light is called the Drawer Full Indicator, which means that the waste drawer is full (or approaching full) and needs to be emptied.

Does Litter-Robot tell you when to add litter?

The Litter-Robot unit detects waste levels in the drawer, while the app allows you to monitor the state of the litter box from your phone. Plus, you’ll receive a notification letting you know when it’s time to empty the waste drawer.

How often should kitty litter be changed?

Twice a week is a general guideline for replacing clay litter, but depending on your circumstances, you may need to replace it every other day or only once a week. If you clean the litter box daily, you might only need to change clumping litter every two to three weeks.

THIS IS UNIQUE:  Do robot butlers exist?

How often do cats poop?

Most cats will poop at least once a day. If they’re healthy, their poop should: Be deep brown in color. Feel not too hard or too soft or mushy.

How long does it take the Litter-Robot to cycle?

After your cat leaves the Globe, the Litter-Robot automatically performs a Clean cycle. The patented sifting system separates the clumps from the clean litter and deposits them into the Waste Drawer below. It takes about 2 ½ minutes. You can also press the Cycle button to start a Clean cycle.

How do you adjust the sensor on Litter-Robot?

Adjust your cat sensor by pressing the Reset button. Test CATS by pressing on the globe just above the entrance in a forward and downward motion. The red light should engage. If the red light does not turn on after applying pressure, check your unit placement (below).

Why does my Litter-Robot say timing?

The Wait Time is the elapsed time starting from when your cat exits the Globe until the unit starts a Clean cycle. It can be set for 3, 7, or 15 minutes. The default Wait Time setting is 7 minutes.

What is a cat sensor fault on the Litter-Robot?

Sometimes after adding litter or replacing litter in the globe, the total weight of the globe becomes high enough that during the rotation or even while stationary (without cat inside) the cat sensor is triggered. If the Cat Sensor is triggered continuously for more than 2 minutes then the red light starts to blink.

Why does my Litter-Robot keep getting stuck?

Check for stuck litter, especially if you recently cleaned your unit (leftover moisture may have interacted with the litter). If you see debris or suspect there is litter caked behind the screen, you will need to clean the Globe (the screen should not be bent outward to clean behind).

THIS IS UNIQUE:  Should Sitemap XML be in robots txt?
Categories AI